This library provides a variety of data descriptor class for Adafruit CircuitPython that makes it really simple to write a device drivers for a I2C and SPI register based devices. Data descriptors act like basic attributes from the outside which makes using them really easy to use.
This driver depends on:
Please ensure all dependencies are available on the CircuitPython filesystem. This is easily achieved by downloading the Adafruit library and driver bundle.
Creating a driver¶
Creating a driver with the register library is really easy. First, import the register modules you need from the available modules:
from adafruit_register import i2c_bit from adafruit_bus_device import i2c_device
Next, define where the bit is located in the device’s memory map:
class HelloWorldDevice: """Device with two bits to control when the words 'hello' and 'world' are lit.""" hello = i2c_bit.RWBit(0x0, 0x0) """Bit to indicate if hello is lit.""" world = i2c_bit.RWBit(0x1, 0x0) """Bit to indicate if world is lit."""
Lastly, we need to add an
i2c_device member of type
that manages sharing the I2C bus for us. Make sure the name is exact, otherwise
the registers will not be able to find it. Also, make sure that the i2c device
def __init__(self, i2c, device_address=0x0): self.i2c_device = i2c_device.I2CDevice(i2c, device_address)
Thats it! Now we have a class we can use to talk to those registers:
import busio from board import * with busio.I2C(SCL, SDA) as i2c: device = HelloWorldDevice(i2c) device.hello = True device.world = True
Adding register types¶
Adding a new register type is a little more complicated because you need to be careful and minimize the amount of memory the class will take. If you don’t, then a driver with five registers of your type could take up five times more extra memory.
First, determine whether the new register class should go in an existing module or not. When in doubt choose a new module. The more finer grained the modules are, the fewer extra classes a driver needs to load in.
Here is the start of the
class RWBit: """ Single bit register that is readable and writeable. Values are `bool` :param int register_address: The register address to read the bit from :param type bit: The bit index within the byte at ``register_address`` """ def __init__(self, register_address, bit): self.bit_mask = 1 << bit self.buffer = bytearray(2) self.buffer = register_address
The first thing done is writing an RST formatted class comment that explains the
functionality of the register class and any requirements of the register layout.
It also documents the parameters passed into the constructor (
configure the register location in the device map. It does not include the
device address or the i2c object because its shared on the device class instance
instead. That way if you have multiple of the same device on the same bus, the
register classes will be shared.
__init__ we only use two member variable because each costs 8 bytes of
memory plus the memory for the value. And remember this gets multiplied by the
number of registers of this type in a driver! Thats why we pack both the
register address and data byte into one bytearray. We could use two byte arrays
of size one but each MicroPython object is 16 bytes minimum due to the garbage
collector. So, by sharing a byte array we keep it to the 16 byte minimum instead
of 32 bytes. Each
memoryview also costs 16 bytes minimum so we avoid them too.
Another thing we could do is allocate the
bytearray only when we need it. This
has the advantage of taking less memory up front but the cost of allocating it
every access and risking it failing. If you want to add a version of
lazily allocates the underlying buffer call it
Ok, onward. To make a data descriptor
we must implement
def __get__(self, obj, objtype=None): with obj.i2c_device: obj.i2c_device.write(self.buffer, end=1, stop=False) obj.i2c_device.readinto(self.buffer, start=1) return bool(self.buffer & self.bit_mask) def __set__(self, obj, value): with obj.i2c_device: obj.i2c_device.write(self.buffer, end=1, stop=False) obj.i2c_device.readinto(self.buffer, start=1) if value: self.buffer |= self.bit_mask else: self.buffer &= ~self.bit_mask obj.i2c_device.write(self.buffer)
As you can see, we have two places to get state from. First,
self stores the
register class members which locate the register within the device memory map.
obj is the driver class that uses the register class which must by
definition provide a
i2c_device. This object does two thing for us:
- Waits for the bus to free, locks it as we use it and frees it after.
- Saves the device address and other settings so we don’t have to.
Note that we take heavy advantage of the
end parameters to the
i2c functions to slice the buffer without actually allocating anything extra.
They function just like
self.buffer[start:end] without the extra allocation.
Thats it! Now you can use your new register class like the example above. Just remember to keep the number of members to a minimum because the class may be used a bunch of times.
Contributions are welcome! Please read our Code of Conduct before contributing to help this project stay welcoming.
To build this library locally you’ll need to install the circuitpython-build-tools package.
python3 -m venv .env source .env/bin/activate pip install circuitpython-build-tools
Once installed, make sure you are in the virtual environment:
Then run the build:
circuitpython-build-bundles --filename_prefix adafruit-circuitpython-register --library_location .
Sphinx is used to build the documentation based on rST files and comments in the code. First, install dependencies (feel free to reuse the virtual environment from above):
python3 -m venv .env source .env/bin/activate pip install Sphinx sphinx-rtd-theme
Now, once you have the virtual environment activated:
cd docs sphinx-build -E -W -b html . _build/html
This will output the documentation to
docs/_build/html. Open the index.html in your browser to
view them. It will also (due to -W) error out on any warning like Travis will. This is a good way to
locally verify it will pass.