Introduction
This library provides a variety of data descriptor class for Adafruit CircuitPython that makes it really simple to write a device drivers for a I2C and SPI register based devices. Data descriptors act like basic attributes from the outside which makes using them really easy to use.
Dependencies
This driver depends on:
Please ensure all dependencies are available on the CircuitPython filesystem. This is easily achieved by downloading the Adafruit library and driver bundle.
Installing from PyPI
On supported GNU/Linux systems like the Raspberry Pi, you can install the driver locally from PyPI. To install for current user:
pip3 install adafruit-circuitpython-register
To install system-wide (this may be required in some cases):
sudo pip3 install adafruit-circuitpython-register
To install in a virtual environment in your current project:
mkdir project-name && cd project-name
python3 -m venv .venv
source .venv/bin/activate
pip3 install adafruit-circuitpython-register
Usage Example
Creating a driver
Creating a driver with the register library is really easy. First, import the register modules you need from the available modules:
from adafruit_register import i2c_bit
from adafruit_bus_device import i2c_device
Next, define where the bit is located in the device’s memory map:
class HelloWorldDevice:
"""Device with two bits to control when the words 'hello' and 'world' are lit."""
hello = i2c_bit.RWBit(0x0, 0x0)
"""Bit to indicate if hello is lit."""
world = i2c_bit.RWBit(0x1, 0x0)
"""Bit to indicate if world is lit."""
Lastly, we need to add an i2c_device
member of type I2CDevice
that manages sharing the I2C bus for us. Make sure the name is exact, otherwise
the registers will not be able to find it. Also, make sure that the i2c device
implements the busio.I2C
interface.
def __init__(self, i2c, device_address=0x0):
self.i2c_device = i2c_device.I2CDevice(i2c, device_address)
Thats it! Now we have a class we can use to talk to those registers:
import busio
from board import *
with busio.I2C(SCL, SDA) as i2c:
device = HelloWorldDevice(i2c)
device.hello = True
device.world = True
Adding register types
Adding a new register type is a little more complicated because you need to be careful and minimize the amount of memory the class will take. If you don’t, then a driver with five registers of your type could take up five times more extra memory.
First, determine whether the new register class should go in an existing module or not. When in doubt choose a new module. The more finer grained the modules are, the fewer extra classes a driver needs to load in.
Here is the start of the RWBit
class:
class RWBit:
"""
Single bit register that is readable and writeable.
Values are `bool`
:param int register_address: The register address to read the bit from
:param type bit: The bit index within the byte at ``register_address``
"""
def __init__(self, register_address, bit):
self.bit_mask = 1 << bit
self.buffer = bytearray(2)
self.buffer[0] = register_address
The first thing done is writing an RST formatted class comment that explains the
functionality of the register class and any requirements of the register layout.
It also documents the parameters passed into the constructor (__init__
) which
configure the register location in the device map. It does not include the
device address or the i2c object because its shared on the device class instance
instead. That way if you have multiple of the same device on the same bus, the
register classes will be shared.
In __init__
we only use two member variable because each costs 8 bytes of
memory plus the memory for the value. And remember this gets multiplied by the
number of registers of this type in a driver! Thats why we pack both the
register address and data byte into one bytearray. We could use two byte arrays
of size one but each MicroPython object is 16 bytes minimum due to the garbage
collector. So, by sharing a byte array we keep it to the 16 byte minimum instead
of 32 bytes. Each memoryview
also costs 16 bytes minimum so we avoid them too.
Another thing we could do is allocate the bytearray
only when we need it. This
has the advantage of taking less memory up front but the cost of allocating it
every access and risking it failing. If you want to add a version of Foo
that
lazily allocates the underlying buffer call it FooLazy
.
Ok, onward. To make a data descriptor
we must implement __get__
and __set__
.
def __get__(self, obj, objtype=None):
with obj.i2c_device as i2c:
i2c.write_then_readinto(self.buffer, self.buffer, out_end=1, in_start=1)
return bool(self.buffer[1] & self.bit_mask)
def __set__(self, obj, value):
with obj.i2c_device as i2c:
i2c.write_then_readinto(self.buffer, self.buffer, out_end=1, in_start=1)
if value:
self.buffer[1] |= self.bit_mask
else:
self.buffer[1] &= ~self.bit_mask
obj.i2c_device.write(self.buffer)
As you can see, we have two places to get state from. First, self
stores the
register class members which locate the register within the device memory map.
Second, obj
is the driver class that uses the register class which must by
definition provide a I2CDevice compatible
object as i2c_device
. This object does two thing for us:
Waits for the bus to free, locks it as we use it and frees it after.
Saves the device address and other settings so we don’t have to.
Note that we take heavy advantage of the start
and end
parameters to the
i2c functions to slice the buffer without actually allocating anything extra.
They function just like self.buffer[start:end]
without the extra allocation.
Thats it! Now you can use your new register class like the example above. Just remember to keep the number of members to a minimum because the class may be used a bunch of times.
Documentation
API documentation for this library can be found on Read the Docs.
For information on building library documentation, please check out this guide.
Contributing
Contributions are welcome! Please read our Code of Conduct before contributing to help this project stay welcoming.